LAN-095e.A0 i.MX 6 Bootjumper Configurations
Table of Contents
Copyrighted products are not explicitly indicated in this manual. The absence of the trademark (™, or ®) and copyright (©) symbols does not imply that a product is not protected. Additionally, registered patents and trademarks are similarly not expressly indicated in this manual.
The information in this document has been carefully checked and is considered to be entirely reliable. However, PHYTEC Messtechnik GmbH assumes no responsibility for any inaccuracies. PHYTEC Messtechnik GmbH neither gives any guarantee nor accepts any liability whatsoever for consequential damages resulting from the use of this manual or its associated product. PHYTEC Messtechnik GmbH reserves the right to alter the information contained herein without prior notification and accepts no responsibility for any damages that might result.
Additionally, PHYTEC Messtechnik GmbH offers no guarantee nor accepts any liability for damages arising from the improper usage or improper installation of the hardware or software. PHYTEC Messtechnik GmbH further reserves the right to alter the layout and/or design of the hardware without prior notification and accepts no liability for doing so.
@ Copyright 2020 PHYTEC Messtechnik GmbH, D-55129 Mainz.
Rights, including those of translation, reprint, broadcast, photomechanical or similar reproduction and storage or processing in computer systems, in whole or in part, are reserved. No reproduction may occur without the express written consent from PHYTEC Messtechnik GmbH.
| EUROPE | NORTH AMERICA | FRANCE | INDIA | CHINA |
Address: | PHYTEC Messtechnik GmbH | PHYTEC America LLC | PHYTEC France | PHYTEC Embedded Pvt. Ltd | PHYTEC Information Technology (Shenzhen) Co. Ltd. |
Ordering Information: | +49 6131 9221-32 | +1 800 278-9913 | +33 2 43 29 22 33 | +91-80-4086 7046/48 sales@phytec.in | +86-755-3395-5875 sales@phytec.cn |
Technical Support: | +49 6131 9221-31 | +1 206 780-9047 | +91-80-4086 7047 support@phytec.in | support@phytec.cn | |
Fax: | +49 6131 9221-33 | +1 206 780-9135 | +33 2 43 29 22 34 | +86-755-3395-5999 | |
Web Site: | http://phytec.in | http://www.phytec.cn |
Introduction
This manual contains tables that show all possible bootjumper configurations for all PHYTEC i.MX 6 products.
Setting marked with bold, blue are the default setting for each board.
If you cannot find your product in the tables below, please contact PHYTEC sales. We will be more then happy to help you.
Bootjumper Configurations
phyFLEX-i.MX 6 RDK Carrier Board (PBA-B-01)
Bootmode | not in use (S3_4) | X_BOOT2 (S3_3) | X_BOOT1 (S3_2) | X_BOOT0 | Boot Source |
---|---|---|---|---|---|
0 | OFF | OFF | OFF | OFF | NAND |
1 | OFF | OFF | OFF | ON | SPI3, CS0 (onboard SPI Flash if populated) |
2 | OFF | OFF | ON | OFF | |
3 | OFF | OFF | ON | ON | SD0 external |
4 | OFF | ON | OFF | OFF | Serial USB OTG (USB0, same as mode 6) |
5 | OFF | ON | OFF | ON | SATA |
6 | OFF | ON | ON | OFF | Serial USB OTG( USB0, same as mode 4) |
7 | OFF | ON | ON | ON | Bootconfig from eFUSE |
phyBOARD-Mira i.MX 6
DIP 1 (S2)
Bootmode | 1 |
---|---|
NAND / eMMC | OFF |
SD Card | ON |
phyBOARD-Nunki i.MX 6
S2
Bootmode | S2 |
---|---|
NAND | OFF |
SD Card | ON |
phyBOARD-Segin i.MX 6UL
J1
Bootmode | 1 |
---|---|
NAND | OPEN |
SD Card | CLOSE |